Utilizei o CrystalDiskInfo no HD do notebook (que pretendo substituir por um SSD no 2º semestre) com Windows e apresentou um alerta amarelo no status de saúde: “Alerta [C5] Current Pending Sector Count: 1” (Dados: Atual: 200, Pior: 200, Limiar: 0, Valor Bruto: 000000000001). Temperatura 42º C.
Estranhamente, o Windows não detectar erros, mas, o software.
Devo ficar muito preocupado? Será que o HD aguenta até que eu possa substitui-lo pelo SSD nos próximos meses?
Somente se estiver tendo travamentos aleatorios no sistema, mas pode ser setor no meio ou fim do disco, então sim e não
1 curtida
Continua acompanhando se o valor vai subindo. Pode ser que fique na mesma e vc troque conforme seu cronograma, ou pode ser que aumente rapidamente e nesse caso seja necessário efetuar uma troca emergencial.
3 curtidas
Aparentemente está normal por enquanto.
@Deleterium Rapaz, até mês passado estava tudo ok, do nada esse disco me apresenta isso. E logo em um péssimo momento para gastos.
Usei o HD Tune aqui e obtive os seguintes resultados:
HD Tune: WDC WD10JPVX-22JC3T0 Health
ID Current Worst ThresholdData Status
(01) Raw Read Error Rate 200 200 51 42 Ok
(03) Spin Up Time 180 177 21 2000 Ok
(04) Start/Stop Count 96 96 0 4971 Ok
(05) Reallocated Sector Count 200 200 140 0 Ok
(07) Seek Error Rate 200 200 0 0 Ok
(09) Power On Hours Count 62 62 0 27993 Ok
(0A) Spin Retry Count 100 100 0 0 Ok
(0B) Calibration Retry Count 100 100 0 0 Ok
(0C) Power Cycle Count 96 96 0 4216 Ok
(BF) G-sense Error Rate 25 25 0 75 Ok
(C0) Power Off Retract Count 200 200 0 239 Ok
(C1) Load Cycle Count 198 198 0 7445 Ok
(C2) Temperature 107 95 0 40 Ok
(C4) Reallocated Event Count 200 200 0 0 Ok
***(C5) Current Pending Sector 200 200 0 1 Ok***
(C6) Offline Uncorrectable 100 253 0 0 Ok
(C7) Ultra DMA CRC Error Count 200 200 0 0 Ok
(C8) Write Error Rate 100 253 0 0 Ok
Power On Time : 27993
Health Status : Ok
HD Tune: WDC WD10JPVX-22JC3T0 Error Scan
Scanned data : 953488 MB
Damaged Blocks : 0.0 %
Elapsed Time : 1:47
Resultados do HDDScan S.M.A.R.T. Report : OK
HDDScan S.M.A.R.T. Report HDD
State:
Model: WDC WD10JPVX-22JC3T0
Firmware: 01.01A01
Serial: WD-WX71EB63PH9P
LBA: 1953525168 (1000 GB)
Report By: HDDSCAN v4.1
Report Date: 01/05/2023 22:34:12
Num Attribute Name Value Worst Raw(hex) Threshold
001 Raw Read Error Rate 200 200 0000000000-002A 051
003 Spin Up Time 180 177 0000000000-07D0 021
004 Start/Stop Count 096 096 0000000000-136B 000
005 Reallocation Sector Count 200 200 0000000000-0000 140
007 Seek Error Rate 200 200 0000000000-0000 000
009 Power-On Hours Count 062 062 0000000000-6D5A 000
010 Spin Retry Count 100 100 0000000000-0000 000
011 Recalibration Retries 100 100 0000000000-0000 000
012 Device Power Cycle Count 096 096 0000000000-1078 000
191 G-sense Rate/Servo tracking 025 025 0000000000-004B 000
192 Emergency Retract Count 200 200 0000000000-00EF 000
193 Load/unload Cycle Count 198 198 0000000000-1D16 000
194 HDA Temperature 104 095 43 C 000
196 Reallocation Event Count 200 200 0000000000-0000 000
*197 Current Pending Errors Count 200 200 0000000000-0001 000*
198 Uncorrectable Errors Count 100 253 0000000000-0000 000
199 UltraDMA CRC Errors 200 200 0000000000-0000 000
200 Multi Zone Error Rate 100 253 0000000000-0000 000
1 curtida
Com o GSmartControl obtive os seguintes resultados:
smartctl 7.2 2020-12-30 r5155 [x86_64-w64-mingw32-w10-b22622] (sf-7.2-1)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue Mobile
Device Model: WDC WD10JPVX-22JC3T0
Serial Number: WD-WX71EB63PH9P
LU WWN Device Id: 5 0014ee 6b25af1b6
Firmware Version: 01.01A01
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon May 01 22:42:42 2023 HPB
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 249) Self-test routine in progress...
90% of test remaining.
Total time to complete Offline
data collection: (17940) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 201) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 42
3 Spin_Up_Time POS--K 180 177 021 - 2000
4 Start_Stop_Count -O--CK 096 096 000 - 4971
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 000 - 0
9 Power_On_Hours -O--CK 062 062 000 - 27994
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 096 096 000 - 4216
191 G-Sense_Error_Rate -O--CK 025 025 000 - 75
192 Power-Off_Retract_Count -O--CK 200 200 000 - 239
193 Load_Cycle_Count -O--CK 198 198 000 - 7446
194 Temperature_Celsius -O---K 104 095 000 - 43
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 1
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 38 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 42 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 42 [17] occurred at disk power-on lifetime: 27976 hours (1165 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 68 00 00 72 49 00 a0 40 00 07:54:10.235 READ FPDMA QUEUED
60 01 00 00 60 00 00 72 48 ff a0 40 00 07:54:10.235 READ FPDMA QUEUED
60 01 00 00 58 00 00 72 48 fe a0 40 00 07:54:10.235 READ FPDMA QUEUED
60 01 00 00 50 00 00 72 48 fd a0 40 00 07:54:10.235 READ FPDMA QUEUED
60 01 00 00 48 00 00 72 48 fc a0 40 00 07:54:10.235 READ FPDMA QUEUED
Error 41 [16] occurred at disk power-on lifetime: 27976 hours (1165 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 78 00 70 00 00 6e a7 b2 c8 40 00 07:53:59.920 READ FPDMA QUEUED
61 00 10 00 68 00 00 00 5e bf 98 40 00 07:53:59.920 WRITE FPDMA QUEUED
60 00 a8 00 58 00 00 72 48 fe a0 40 00 07:53:59.920 READ FPDMA QUEUED
60 01 00 00 50 00 00 72 48 fd a0 40 00 07:53:59.920 READ FPDMA QUEUED
60 01 00 00 48 00 00 72 48 fc a0 40 00 07:53:59.920 READ FPDMA QUEUED
Error 40 [15] occurred at disk power-on lifetime: 27976 hours (1165 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 e0 00 00 72 49 00 a0 40 00 07:53:41.038 READ FPDMA QUEUED
60 01 00 00 d8 00 00 72 48 ff a0 40 00 07:53:41.038 READ FPDMA QUEUED
60 01 00 00 d0 00 00 72 48 fe a0 40 00 07:53:41.038 READ FPDMA QUEUED
60 01 00 00 c8 00 00 72 48 fd a0 40 00 07:53:41.038 READ FPDMA QUEUED
60 01 00 00 c0 00 00 72 48 fc a0 40 00 07:53:41.038 READ FPDMA QUEUED
Error 39 [14] occurred at disk power-on lifetime: 27976 hours (1165 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 a8 00 c8 00 00 72 48 fe a0 40 00 07:53:08.754 READ FPDMA QUEUED
60 01 00 00 c0 00 00 72 48 fd a0 40 00 07:53:08.754 READ FPDMA QUEUED
60 01 00 00 b8 00 00 72 48 fc a0 40 00 07:53:08.754 READ FPDMA QUEUED
60 01 00 00 b0 00 00 72 48 fb a0 40 00 07:53:08.753 READ FPDMA QUEUED
60 01 00 00 a8 00 00 72 48 fa a0 40 00 07:53:08.753 READ FPDMA QUEUED
Error 38 [13] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 18 00 00 07 e1 a2 70 40 00 09:54:42.044 WRITE FPDMA QUEUED
61 00 10 00 10 00 00 00 62 c8 a8 40 00 09:54:42.044 WRITE FPDMA QUEUED
60 00 08 00 08 00 00 2a fc 23 bd 40 00 09:54:42.044 READ FPDMA QUEUED
60 00 08 00 00 00 00 72 48 fa 40 40 00 09:54:42.044 READ FPDMA QUEUED
60 00 48 00 f8 00 00 03 c4 53 30 40 00 09:54:42.044 READ FPDMA QUEUED
Error 37 [12] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 98 00 00 00 5e c0 08 40 00 09:54:38.242 WRITE FPDMA QUEUED
61 00 18 00 90 00 00 5f 4f 79 30 40 00 09:54:38.242 WRITE FPDMA QUEUED
60 00 10 00 88 00 00 2a fc 23 8d 40 00 09:54:38.242 READ FPDMA QUEUED
61 00 08 00 80 00 00 37 6b 81 30 40 00 09:54:38.242 WRITE FPDMA QUEUED
60 00 08 00 78 00 00 72 48 fa 40 40 00 09:54:38.226 READ FPDMA QUEUED
Error 36 [11] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 18 00 f8 00 00 00 31 b5 70 40 00 09:54:34.255 WRITE FPDMA QUEUED
60 00 28 00 f0 00 00 05 c1 83 78 40 00 09:54:34.255 READ FPDMA QUEUED
60 00 23 00 e8 00 00 02 f3 e2 58 40 00 09:54:34.255 READ FPDMA QUEUED
61 00 08 00 e0 00 00 07 e1 a2 70 40 00 09:54:34.255 WRITE FPDMA QUEUED
61 00 28 00 d8 00 00 58 fd 5d 90 40 00 09:54:34.254 WRITE FPDMA QUEUED
Error 35 [10] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 50 00 00 26 55 87 18 40 00 09:54:30.145 READ FPDMA QUEUED
60 01 00 00 48 00 00 26 55 86 18 40 00 09:54:30.145 READ FPDMA QUEUED
60 01 00 00 40 00 00 26 55 85 18 40 00 09:54:30.130 READ FPDMA QUEUED
60 01 00 00 38 00 00 26 55 84 18 40 00 09:54:30.128 READ FPDMA QUEUED
60 01 00 00 30 00 00 26 55 83 18 40 00 09:54:30.126 READ FPDMA QUEUED
Error 34 [9] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 01 00 00 e8 00 00 72 c5 61 68 40 00 09:54:26.215 WRITE FPDMA QUEUED
61 01 00 00 e0 00 00 72 c5 60 68 40 00 09:54:26.214 WRITE FPDMA QUEUED
61 01 00 00 d8 00 00 72 c5 5f 68 40 00 09:54:26.214 WRITE FPDMA QUEUED
61 01 00 00 d0 00 00 72 c5 5e 68 40 00 09:54:26.214 WRITE FPDMA QUEUED
61 01 00 00 c8 00 00 72 c5 5d 68 40 00 09:54:26.213 WRITE FPDMA QUEUED
Error 33 [8] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 28 00 78 00 00 09 52 e1 12 40 00 09:53:43.614 READ FPDMA QUEUED
60 01 00 00 70 00 00 72 49 00 a0 40 00 09:53:43.614 READ FPDMA QUEUED
60 01 00 00 68 00 00 72 48 ff a0 40 00 09:53:43.614 READ FPDMA QUEUED
60 01 00 00 60 00 00 72 48 fe a0 40 00 09:53:43.614 READ FPDMA QUEUED
60 01 00 00 58 00 00 72 48 fd a0 40 00 09:53:43.614 READ FPDMA QUEUED
Error 32 [7] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 98 00 00 37 5d 19 58 40 00 09:50:49.764 WRITE FPDMA QUEUED
61 00 08 00 90 00 00 01 42 f6 10 40 00 09:50:49.763 WRITE FPDMA QUEUED
61 00 08 00 88 00 00 37 5d 17 90 40 00 09:50:49.763 WRITE FPDMA QUEUED
61 00 08 00 80 00 00 00 4e 7f a0 40 00 09:50:49.763 WRITE FPDMA QUEUED
61 00 08 00 78 00 00 08 43 ed a8 40 00 09:50:49.763 WRITE FPDMA QUEUED
Error 31 [6] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 18 00 98 00 00 00 63 7b 70 40 00 09:50:45.970 WRITE FPDMA QUEUED
61 00 08 00 90 00 00 37 5c c6 60 40 00 09:50:45.970 WRITE FPDMA QUEUED
61 00 08 00 88 00 00 07 e1 a2 58 40 00 09:50:45.970 WRITE FPDMA QUEUED
61 00 08 00 80 00 00 59 0d fe 18 40 00 09:50:45.969 WRITE FPDMA QUEUED
61 00 18 00 78 00 00 00 5e bf 70 40 00 09:50:45.969 WRITE FPDMA QUEUED
Error 30 [5] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 f0 00 00 72 48 fa 40 40 00 09:50:42.075 READ FPDMA QUEUED
61 00 08 00 e8 00 00 07 e1 a2 58 40 00 09:50:42.075 WRITE FPDMA QUEUED
61 00 08 00 e0 00 00 00 5e bf f0 40 00 09:50:42.075 WRITE FPDMA QUEUED
60 00 40 00 d8 00 00 53 e8 2c 98 40 00 09:50:42.075 READ FPDMA QUEUED
61 00 10 00 d0 00 00 01 42 f6 a8 40 00 09:50:42.075 WRITE FPDMA QUEUED
Error 29 [4] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 98 00 00 52 9a 47 00 40 00 09:50:38.439 WRITE FPDMA QUEUED
61 00 20 00 90 00 00 00 72 90 40 40 00 09:50:38.439 WRITE FPDMA QUEUED
61 00 08 00 88 00 00 00 63 7a 50 40 00 09:50:38.438 WRITE FPDMA QUEUED
61 00 20 00 80 00 00 00 63 7a 20 40 00 09:50:38.438 WRITE FPDMA QUEUED
60 00 20 00 78 00 00 21 85 c0 40 40 00 09:50:38.438 READ FPDMA QUEUED
Error 28 [3] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 c8 00 00 00 5e bf e0 40 00 09:50:34.753 WRITE FPDMA QUEUED
61 00 08 00 c0 00 00 00 5e bf 60 40 00 09:50:34.753 WRITE FPDMA QUEUED
61 00 58 00 b8 00 00 00 5f a2 88 40 00 09:50:34.752 WRITE FPDMA QUEUED
61 01 00 00 b0 00 00 00 5f a1 88 40 00 09:50:34.716 WRITE FPDMA QUEUED
61 01 00 00 a8 00 00 00 5f a0 88 40 00 09:50:34.716 WRITE FPDMA QUEUED
Error 27 [2] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 f0 00 00 16 65 41 40 40 00 09:47:09.469 WRITE FPDMA QUEUED
61 00 08 00 e8 00 00 01 42 f6 a8 40 00 09:47:09.469 WRITE FPDMA QUEUED
60 00 38 00 e0 00 00 02 ea 47 68 40 00 09:47:09.469 READ FPDMA QUEUED
61 00 10 00 d8 00 00 00 04 6f c0 40 00 09:47:09.469 WRITE FPDMA QUEUED
61 00 08 00 d0 00 00 00 5e bf 60 40 00 09:47:09.469 WRITE FPDMA QUEUED
Error 26 [1] occurred at disk power-on lifetime: 27963 hours (1165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 e0 00 00 72 48 fa 40 40 00 09:47:05.773 READ FPDMA QUEUED
60 00 20 00 c0 00 00 5e 9c a7 20 40 00 09:47:05.773 READ FPDMA QUEUED
60 00 20 00 b0 00 00 5b d5 b7 20 40 00 09:47:05.773 READ FPDMA QUEUED
61 01 00 00 98 00 00 00 5f 68 88 40 00 09:47:05.772 WRITE FPDMA QUEUED
60 00 08 00 90 00 00 70 53 fa 88 40 00 09:47:05.772 READ FPDMA QUEUED
Error 25 [0] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 90 00 00 70 53 fa 88 40 00 09:47:02.114 READ FPDMA QUEUED
60 00 08 00 78 00 00 70 53 fa 28 40 00 09:47:02.113 READ FPDMA QUEUED
60 00 08 00 70 00 00 70 53 fa 20 40 00 09:47:02.113 READ FPDMA QUEUED
61 00 08 00 68 00 00 00 62 d1 08 40 00 09:47:02.109 WRITE FPDMA QUEUED
61 00 08 00 60 00 00 00 62 cf 98 40 00 09:47:02.109 WRITE FPDMA QUEUED
Error 24 [23] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 10 00 00 72 48 fa 10 40 00 09:46:58.118 READ FPDMA QUEUED
61 00 08 00 08 00 00 00 62 cc 10 40 00 09:46:58.118 WRITE FPDMA QUEUED
61 00 08 00 00 00 00 00 63 a8 08 40 00 09:46:58.118 WRITE FPDMA QUEUED
60 00 80 00 f8 00 00 72 48 fa 10 40 00 09:46:58.118 READ FPDMA QUEUED
60 00 08 00 f0 00 00 72 48 f9 a8 40 00 09:46:58.118 READ FPDMA QUEUED
Error 23 [22] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 01 00 c8 00 00 00 08 c7 30 40 00 09:46:53.813 READ FPDMA QUEUED
61 00 10 00 c0 00 00 00 5e bf e0 40 00 09:46:53.812 WRITE FPDMA QUEUED
60 00 a8 00 b8 00 00 72 48 fe a0 40 00 09:46:53.812 READ FPDMA QUEUED
60 01 00 00 b0 00 00 72 48 fd a0 40 00 09:46:53.812 READ FPDMA QUEUED
60 01 00 00 a8 00 00 72 48 fc a0 40 00 09:46:53.812 READ FPDMA QUEUED
Error 22 [21] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 90 00 00 00 65 11 10 40 00 09:46:49.578 WRITE FPDMA QUEUED
60 00 28 00 88 00 00 30 23 48 a0 40 00 09:46:49.578 READ FPDMA QUEUED
61 00 08 00 80 00 00 00 5e bf e0 40 00 09:46:49.578 WRITE FPDMA QUEUED
60 00 28 00 78 00 00 30 23 48 a0 40 00 09:46:49.578 READ FPDMA QUEUED
60 00 a8 00 70 00 00 72 48 fe a0 40 00 09:46:49.578 READ FPDMA QUEUED
Error 21 [20] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: WP at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 38 00 90 00 00 00 5f 68 50 40 00 09:46:45.882 WRITE FPDMA QUEUED
61 01 00 00 88 00 00 00 5f 67 50 40 00 09:46:45.882 WRITE FPDMA QUEUED
60 00 40 00 80 00 00 10 99 b3 08 40 00 09:46:45.882 READ FPDMA QUEUED
61 00 20 00 78 00 00 16 65 40 00 40 00 09:46:45.881 WRITE FPDMA QUEUED
60 01 00 00 70 00 00 72 49 06 48 40 00 09:46:45.881 READ FPDMA QUEUED
Error 20 [19] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 70 00 00 72 48 fa 40 40 00 09:37:20.870 READ FPDMA QUEUED
60 00 80 00 68 00 00 70 5d c7 40 40 00 09:37:20.868 READ FPDMA QUEUED
60 01 00 00 60 00 00 6e 4d a7 c0 40 00 09:37:20.862 READ FPDMA QUEUED
60 00 30 00 58 00 00 08 6b 96 00 40 00 09:37:20.855 READ FPDMA QUEUED
60 00 08 00 50 00 00 00 63 fd e0 40 00 09:37:20.838 READ FPDMA QUEUED
Error 19 [18] occurred at disk power-on lifetime: 27962 hours (1165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 72 48 fa 40 40 00 Error: UNC at LBA = 0x7248fa40 = 1917385280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 08 00 00 00 93 cc a0 40 00 09:37:17.101 READ FPDMA QUEUED
60 00 80 00 f8 00 00 70 54 b9 c0 40 00 09:37:17.099 READ FPDMA QUEUED
61 00 08 00 c8 00 00 00 64 93 c0 40 00 09:37:17.099 WRITE FPDMA QUEUED
61 00 08 00 c0 00 00 00 64 8e d8 40 00 09:37:17.099 WRITE FPDMA QUEUED
61 00 08 00 b8 00 00 00 64 69 d8 40 00 09:37:17.098 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 27994 -
# 2 Short offline Aborted by host 10% 1792 -
# 3 Short offline Aborted by host 10% 1792 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: DST executing in background (3)
Current Temperature: 43 Celsius
Power Cycle Min/Max Temperature: 39/46 Celsius
Lifetime Min/Max Temperature: 0/52 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 128 (38)
Index Estimated Time Temperature Celsius
39 2023-05-01 20:35 40 *********************
... ..( 59 skipped). .. *********************
99 2023-05-01 21:35 40 *********************
100 2023-05-01 21:36 39 ********************
... ..( 16 skipped). .. ********************
117 2023-05-01 21:53 39 ********************
118 2023-05-01 21:54 40 *********************
... ..( 10 skipped). .. *********************
1 2023-05-01 22:05 40 *********************
2 2023-05-01 22:06 41 **********************
... ..( 4 skipped). .. **********************
7 2023-05-01 22:11 41 **********************
8 2023-05-01 22:12 42 ***********************
... ..( 3 skipped). .. ***********************
12 2023-05-01 22:16 42 ***********************
13 2023-05-01 22:17 43 ************************
... ..( 24 skipped). .. ************************
38 2023-05-01 22:42 43 ************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 56472 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 6 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 31178 Vendor specificRelaxa que aparecer Pending Sectores em HDs é normal até certo limite e só ás vezes deixa o sistema lento e raramente corrompe algum arquivo importante.
2 curtidas
Obrigado por me tranquilizar um pouco mais. Como eu mencionei, já está nos planos a aquisição de um SSD nos próximos meses para essa máquina, mas, quanto mais meses eu tiver melhor porque irei conseguir um novo disco de qualidade melhor, se tiver que comprar “no susto” agora, serei obrigado a comprar o SSD mais simples o possível por ter outros gastos no momento.
Este tópico foi fechado automaticamente. Novas respostas não são mais permitidas.